24. W5100S/W5500+RP2040 Raspberry Pi Pico＜PHY status mode control＞

Article directory

  • 1 Introduction
  • 2. Related introduction
    • 2.1 Brief description
    • 2.2 Principle
    • 2.3 Advantages & Applications
  • 3. WIZnet Ethernet chip
  • 4. PHY mode configuration test
    • 4.1 Program flow chart
    • 4.2 Test preparation
    • 4.3 Connection method
    • 4.4 Related code
    • 4.5 Test phenomena
  • 5. Precautions
  • 6. Related links

1. Preface

W5100S/W5500 not only supports automatic PHY auto-negotiation, but also supports user-defined PHY modes, including 10M/100M, half-duplex/full-duplex, power-down mode, etc.

This chapter will use W5100S/W5500 + Raspberry Pi RP2040 to configure and test one by one.

W5100S/W5500 is an embedded Ethernet controller integrating a full hardware TCP/IP protocol stack. It is also an industrial-grade Ethernet control chip. Using the W5100S/W5500 in Ethernet applications makes it easier for users to connect and communicate remotely between devices.

2. Related introduction

2.1 Brief description

? The 10M and 100M of PHY refer to the network transmission rate, which means the data rate of transmitting 10 megabits (Mbit) and 100 megabits (Mbit) per second respectively. These rates are commonly used to describe the performance of local area network (LAN) and wide area network (WAN) connections.

? Half-duplex and full-duplex refer to the working modes of network connections. Half-duplex means that both parties to the data connection can only perform an operation mode in which one party sends data and the other party receives data at the same time. Full-duplex refers to the operating mode in which both parties of the data connection can send and receive data at the same time. The full-duplex mode does not require direction switching, so there is no time delay caused by switching operations, which is very beneficial for interactive applications that cannot have time delays (such as remote monitoring and control systems).

? The PHY power-down mode means that when the PHY chip encounters an abnormal situation or needs to save energy, it will automatically enter the power-down mode and shut down unnecessary equipment and functions to reduce energy consumption and extend the service life of the equipment. In power-down mode, the operation of some devices will be affected, such as reduced screen brightness, reduced processor frequency, etc. Power-down mode is an energy-saving technology that can achieve efficient use of energy while ensuring the normal operation of the equipment.

2.2 Principle

? According to actual needs, you can configure the PHY in different modes by writing the PHYCR0 and PHYCR1 register parameters.

2.3 Advantages & Applications

  • Energy saving: The low-power PHY chip can effectively reduce power consumption while maintaining high performance. For battery-powered devices, it can greatly extend the working time of the device.

  • Thermal design optimization: The low-power PHY chip has been designed with thermal performance optimization in mind and can maintain good heat dissipation performance under high load conditions, thereby ensuring efficient and stable operation of the chip.

  • Extend the service life of the device: Since the low-power PHY chip can effectively reduce power consumption, it can reduce the heat accumulation and loss of the device, thereby extending the service life of the device.

  • Comply with green environmental protection requirements: As people’s awareness of environmental protection increases, the high efficiency and energy saving of electronic equipment has also become a focus of attention. Low-power PHY chips can better meet the requirements of green environmental protection and contribute to the green development of electronic equipment.

  • Wide range of applications: Low-power PHY chips are widely used in various fields, such as the Internet of Things, smart homes, medical equipment, etc. These fields require long-term work and efficient performance, and low-power PHY chips can just meet the requirements. these needs.

? In short, the advantages of PHY’s low power consumption are mainly reflected in energy saving, thermal design optimization, extended equipment service life, compliance with green environmental protection requirements and wide application. These advantages make low power PHY chips widely used in various fields. application and promotion.

3. WIZnet Ethernet chip

WIZnet mainstream hardware protocol stack Ethernet chip parameter comparison

Model Embedded Core Host I/F TX/RX Buffer HW Socket Network Performance
W5100S TCP/IPv4, MAC & PHY 8 bit BUS, SPI 16 KB 4 Max 25 Mbps
W6100 TCP/IPv4/IPv6, MAC & PHY 8 bit BUS, Fast SPI 32 KB 8 Max 25 Mbps
W5500 TCP/IPv4, MAC & PHY Fast SPI 32 KB 8 Max 15 Mbps
  1. W5100S/W6100 supports 8-bit data bus interface, and the network transmission speed will be better than W5500.
  2. W6100 supports IPv6 and is Pin to Pin compatible with W5100S. If users who already use W5100S need to support IPv6, they can directly switch to it.
  3. W5500 has more sockets and send and receive buffers than W5100S

4. PHY mode configuration test

4.1 Program flow chart

4.2 Test preparation

Software:

  • Visual Studio Code
  • WIZnet UartTool

Hardware:

  • W5100SIO module + RP2040 Raspberry Pi Pico development board or WIZnet W5100S-EVB-Pico development board
  • Micro USB interface data cable
  • TTL to USB
  • cable

4.3 Connection method

  • Connect the USB port of the PC through the data cable (mainly used for burning programs, but can also be used as a virtual serial port)
  • Convert TTL serial port to USB and connect the default pin of UART0:
    • RP2040 GPIO 0 (UART0 TX) <----> USB_TTL_RX
    • RP2040 GPIO 1 (UART0 RX) <----> USB_TTL_TX
  • When using the module to connect RP2040 for wiring
    • RP2040 GPIO 16 <----> W5100S MISO
    • RP2040 GPIO 17 <----> W5100S CS
    • RP2040 GPIO 18 <----> W5100S SCK
    • RP2040 GPIO 19 <----> W5100S MOSI
    • RP2040 GPIO 20 <----> W5100S RST
  • Directly connect to the PC network port through a network cable (or: both the PC and the device are connected to the switch or router LAN port through a network cable)

4.4 related code

? Open the low_power.c file (path: examples/low_power/low_power.c) to see the specific implementation:

? You can see that the network information is configured in dhcp mode. Therefore, after the master control and W5100S are initialized, DHCP initialization will be performed, and then a timer initialization will be added for timing during the dhcp process for timeout processing; then Enter dhcp to configure network information. If it fails, use static configuration information. Then configure the PHY to 10M mode, 100M mode, power-down mode and read back the print configuration. Finally, enter while blocking, as shown below:

/* Network information to be configured. */
wiz_NetInfo net_info = {<!-- -->
    .mac = {<!-- -->0x00, 0x08, 0xdc, 0x11, 0x22, 0x33}, // Configured MAC address
    .ip = {<!-- -->192, 168, 1, 10}, // Configured IP address
    .sn = {<!-- -->255, 255, 255, 0}, // Configured subnet mask
    .gw = {<!-- -->192, 168, 1, 1}, // Configured gateway
    .dns = {<!-- -->8, 8, 8, 8}, // Configured domain address
    .dhcp = NETINFO_DHCP}; // Configured dhcp model,NETINFO_DHCP:use dhcp; NETINFO_STATIC: use static ip.

static uint8_t ethernet_buf[ETHERNET_BUF_MAX_SIZE] = {<!-- -->
    0,
}; // Send and receive cachestatic

static uint8_t breakout_flag = 0; // Define the DHCP acquisition flag

int main()
{<!-- -->
    struct repeating_timer timer; // Define the timer structure
    wiz_NetInfo get_info; // Stores the read configuration information
    wiz_PhyConf phy_conf, get_conf;

    /* MCU init */
    stdio_init_all(); // Initialize the main control peripheral
    wizchip_initialize(); // Initialize the chip interface
    wizchip_setnetinfo( & amp;net_info); // Configure once first

    /*dhcp init*/
    DHCP_init(SOCKET_ID, ethernet_buf); // DHCP initialization
    add_repeating_timer_ms(1000, repeating_timer_callback, NULL, & timer); // Add DHCP 1s Tick Timer handler

    printf("wiznet chip low power example.\r\
");
    network_init( & amp;net_info); // Configuring Network Information
    print_network_information( & amp;get_info); // Read back the configuration information and print it

    /* config init massage */
    phy_conf.by = PHY_CONFBY_SW; // Use software config
    phy_conf.mode = PHY_MODE_MANUAL; // User config mode
    phy_conf.duplex = PHY_DUPLEX_FULL; // Full duplex
    phy_conf.speed = PHY_SPEED_100; // Speed

    /* setting phy 100M mode */
    ctlwizchip(CW_SET_PHYCONF, & amp;phy_conf);
    ctlwizchip(CW_GET_PHYCONF, & amp;get_conf);

    printf("The current Mbtis speed : %d\r\
", get_conf.speed == PHY_SPEED_100 ? 100 : 10);
    printf("The current Duplex Mode : %s\r\
", get_conf.duplex == PHY_DUPLEX_HALF ? "Half-Duplex" : "Full-Duplex");

    /* setting phy 10M mode */
    phy_conf.speed = PHY_SPEED_10;
    ctlwizchip(CW_SET_PHYCONF, & amp;phy_conf);
    ctlwizchip(CW_GET_PHYCONF, & amp;get_conf);

    printf("The current Mbtis speed : %d\r\
", get_conf.speed == PHY_SPEED_100 ? 100 : 10);
    printf("The current Duplex Mode : %s\r\
", get_conf.duplex == PHY_DUPLEX_HALF ? "Half-Duplex" : "Full-Duplex");

    /* setting phy low power mode */
#if (_WIZCHIP_ == W5100S)
    wizphy_setphypmode(PHY_POWER_DOWN);
    printf("The current phy is : %s\r\
", (read_phy_pwdn(PHYCR1) & amp; (1 << 5)) ? "normal mode" : "power down mode");
    printf("FHY is in power down state and cannot be ping reply.\r\
");
#elif (_WIZCHIP_ == W5500)
    setPHYCFGR((uint8_t) PHYCFGR_RST);
    setPHYCFGR(PHYCFGR_OPMDC_PDOWN);
    printf("The current phy is : %s\r\
", (getPHYCFGR() & PHYCFGR_OPMDC_PDOWN) ? "power down mode" : "normal mode");
    printf("FHY is in power down state and cannot be ping reply.\r\
");
#endif


    while(true)
    {<!-- -->
        
    }
}

4.5 Test phenomenon

? After the hardware connection is correct, compile the burning program, open WIZ UartTool, select the corresponding COM port, and fill in the parameters: baud rate 115200, 8 data bits, 1 stop bit, no parity bit, no flow control, fill in After completing the parameters, click open to open and observe the information printed by the serial port to obtain the device operating status; you can see the information read back: the PHY enters the corresponding mode in sequence according to the configuration, as shown in the following figure:

5. Notes

  • After entering power-down mode, data cannot be sent or received, and ping requests will not be replied to;
  • If we want to use WIZnet’s W5500 to implement the example in this chapter, we only need to modify two places:

  1. Find the header file wizchip_conf.h under library/ioLibrary_Driver/Ethernet/, and change the _WIZCHIP_ macro definition to W5500.

  2. Find the CMakeLists.txt file under the library and set COMPILE_SEL to ON. OFF is W5100S and ON is W5500.

    6. Related links

    WIZnet official website

    WIZnet official library link

    Routine link in this chapter

    If you want to know more, leave a comment!